The prolonged oil saw the use and maintenance of the three problem

Release date: 2020-07-11
The prolonged chain saw is the most widely used in many garden machine products, one of the most frequently used power tools. With very sharp serrated and used for high-speed cutting of timber, and therefore the use of its operating, more stringent safety precautions need to be taken. Any non-standard operations, timely maintenance will be the formation of a certain degree of security risk, users need to pay attention to. The prolonged INDUSTRY Chainsaws production. Manufacturers technical experts concluded a series of chain saw use and maintenance tips and precautions, and to share with our customers.
1, durable chain saw saw chain lubrication should always ensure
Lubrication of chain saws and guides for the use of the chain saw, its important. New saw chain must have been a small amount of lubricant thrown Do not work in the case of the saw chain lubrication. If the saw chain dry run, cutting tools will soon be damaged and can no longer be repaired. So, before starting work, be sure to check the amount of oil lubricants saw chain lubrication and fuel tank.
Automatic and reliable lubrication of chain saws and guides, prolonged Industrial suggested the use of high-quality, small chain saws and guides lubricants environmental pollution, such as anti-aging ability, readily biodegradable lubricants. If aging ability is low, the lubricating oil is easy resin, a precipitate will form a difficult to get rid of the rigid, especially in the transmission parts of the saw chain around, the clutch, and on the saw chain. Severe stuck oil pump. In addition, the non-use of waste lubricating oil. Waste lubricating oil does not have the required ability to lubricate and many contacts waste oil may cause skin cancer but also damage the environment, waste lubricating oil.
Shall be added to increase fuel full of saw chain lubricants must ensure that each fuel exhaustion, the saw chain lubricants box a little remaining oil. If there is not reduced in the amount of oil in the lubricating oil tank, may be due to clogging of the lubricating oil passage. To check the saw chain lubrication, cleaning oil line, when necessary, to the service dealer for assistance.
Machinery for the new factory, to avoid unnecessary high load operation in the run-in period, and, therefore, do not in the first three boxes run out of fuel before high-speed idling. Moving parts must be run-in with each other in the run-in period, so in the meantime, the short cylinder has a larger frictional resistance. The engine reaches its maximum power about 5-15 box oil runs out. Saws during normal operation, not the oil mixing ratio is adjusted too low in order to significantly increase the power, which may damage the engine.
In addition, you should always check the saw chain tension. Compared with the longer period of time has been put into use the saw chain saws require more frequent oil tighten. Usually, in the cold state, the saw chain the guide plate side engaging but still able to hand pull along the guide plate, then the correct degree of tension. Reaches operating temperature, the saw chain expansion, begins to relax. Guides is not allowed under the side of the transmission link from the guide slot, or the saw chain will fall off. Necessary to re-tighten the saw chain. Cooling, the saw chain will shrink. Loosen saw chain, otherwise it will damage the crankshaft and bearings.
2, durable oil saw Mo overlooked the details
Durable chain saw use, there are a few details of the operation requires the user to pay special attention to. First, start the chain saw, Mo will start hove to at the end. Gently pull start handle startup, until the stop position, then quickly pulling force at the same time by pressing down on the front handle. During use, should not be the starter cord completely pulled up to the end, otherwise it might pull it off. Day-to-day use, users often do not pay attention to this detail, the passage of time, the start rope easily damaged. Note also that, do not let the boot handle free bounce should slowly back into the enclosure so that the starter rope can be rolled up.
Secondly, after prolonged operation of the engine to the maximum throttle, it is necessary to let the idle period of time in order to cool the air stream, and the release of most of the heat in the engine. This should avoid the components installed on the engine (ignition, carburetor) thermal overload.
Again, if the engine power is decreased, it may be due to the air filter is dirty. Removing carburetor cover, remove the air filter, the clear around the filter is dirty, and the filter of the two parts separated, with the palm Shan net filters, or to the compressed air from the inside outward blown clean.
If the filter dirt stuck filter on a dedicated cleaner or clean, non-flammable cleaning fluid (such as warm, soapy water) Wash and dry. Do not use a brush to clean the hair quality filter.
Reinstall the air filter, remember to check the damper and torsion spring position is correct.
3, durable Chainsaw aftercare timely and thorough
Maintenance of the chain saw, the most important is that chain. Proper maintenance and sharpening chain just a very small pressure can easily saw into the wood. Routine maintenance, pay attention to check whether there are cracks and broken rivet saw chain links. Replace the saw chain on that broken or worn parts, and then with the new shape and the same size as the original parts. Carbide saw chain is particularly abrasion resistance.
Chain sharpening work is usually done by the service dealer. Sharpening must be maintained when the sawtooth angle. All jagged angles must be the same, if different, the Saw transfer would not be smooth, and badly worn until the saw-strand breaks. The length must also be identical for all serrated. If different, tooth height will be different, it will also cause the saw chain rotation is not smooth and eventually breaks. Sharpening to thoroughly clean the saw chain, clean attached the above file thorn or dust and lubricate the saw chain. If a long time without the need to ensure that the saw chain in a well-oiled state store.
Store chain saw for a long time, in a well-ventilated place the fuel tank empty and clean. Always run the engine carburetor dries, to prevent carburetor diaphragm stick together. Remove the saw chain and guide plate clean, then sprayed with anti-rust oil. Thoroughly clean the equipment, especially the cylinder cooling fins and air filters. If you are using biological saw chain lubricants, lubricating oil tank will have to fill.
It should be noted that, even in accordance with the regulations require the use and maintenance of a chain saw, some parts of the power tool will have the normal wear and tear, and must therefore be based on the model and use of the parts to be replaced in a timely manner. These components include: the chain, the guide plate, transmission components (clutch, the clutch drum, the sprocket), the filter, the starter device, the spark plug, and the vibration damping system parts, etc..